Shandong BTP-2002NP Manual de usuario

USER’S MANUAL Label Printer BTP-L580 Shandong New Beiyang Information Technology Co., Ltd. ORIENT Technologies b.v.

BTP-L580 User’s Manual 91 Introduction 1.1 Outline BTP-L580 thermal label printer has high performance. It can be used f

BTP-L580 User’s Manual 102 Main Specification 2.1 Technical Specification Item Parameter Print Method Direct Thermal

BTP-L580 User’s Manual 112.2 Cutter Specification Item parameter Note Cutter type Slide cutter Cutting time 600m

BTP-L580 User’s Manual 12¾ Paper transmittance Label: transmittance <18%; Base Liner: transmittance >47% ¾ Paper

BTP-L580 User’s Manual 13 If the paper is contaminated by a chemical or oil, it may discolor or lose heat sensitivity

BTP-L580 User’s Manual 142.4.2 Tear off position In normal printing mode, tear off position should be: L1: about 30m

BTP-L580 User’s Manual 153 Outline and Parts 3.1 Outline and Parts 1 – Paper-near-end sensor lever (only for rec

BTP-L580 User’s Manual 16Functions of parts: a) Spindle for label roll It is highly recommended to us

BTP-L580 User’s Manual 17Printer will quit standby status after pressing the FEED button for a short time and a long tim

BTP-L580 User’s Manual 18 Notices:  The paper guide is an indispensable part of the printer and should be kept wit

BTP-L580 User’s Manual 1Content GENERAL SAFETY INSTRUCTION ...7 1 INTRODUCTI

BTP-L580 User’s Manual 19 Caution:  The temperature of the print-head is detected by means of a thermistor sensor. If

BTP-L580 User’s Manual 204 Installation 4.1 Unpacking Check whether all items, that are listed on the packing list are p

BTP-L580 User’s Manual 214.3 Connecting the Power Adapter 1) Ensure that the printer power is turned off. 2）Insert the

BTP-L580 User’s Manual 224.4 Connecting interface cable 1) Ensure the printer power is turned off. 2) Connect the suita

BTP-L580 User’s Manual 234.6 Paper roll loading 4.6.1 Confirm the paper type After connecting the printer to the power s

BTP-L580 User’s Manual 24paper path direction. Note: without paper guide: 82.5 ± 0.5mm Paper guide in the slot

BTP-L580 User’s Manual 25 Press FEED button for two short times and one long time to enter into the Print Self T

BTP-L580 User’s Manual 265 Printer routine maintenance Caution:  Before starting routine maintenance, ensure that the

BTP-L580 User’s Manual 275.3 Clearing of a paper jam Remove the paper, if one of the following phenomena occurs: ¾ The

BTP-L580 User’s Manual 286 Interface signal 6.1 Parallel interface Parallel interface can work in IEEE 1284 compatible m

BTP-L580 User’s Manual 24.6.1 Confirm the paper type...23 4.6.2 Load/rep

BTP-L580 User’s Manual 2927 Signal Ground (Data 8) 28 Signal Ground (PError, Select, and nAck) 29 Signal Ground

BTP-L580 User’s Manual 306.3 USB interface ¾ Parameters Data transmission: Support USB1.1 protocol Connector (Printer

BTP-L580 User’s Manual 31z Supports printer status query and interface module maintenance based on HTTP. ¾ Interface si

BTP-L580 User’s Manual 32z UDP z DHCP z TFTP z HTTP WLAN interface uses wireless USB network card of which the main spec

BTP-L580 User’s Manual 335 － NC 6 GND Common port with circuit Caution:  Do not allow disconnection or connection of

BTP-L580 User’s Manual 347 Troubleshooting Refer to this section if the printer has any problems. If the problem cannot

BTP-L580 User’s Manual 35Paper cannot be fed out properly Paper jam Open top cover and check paper path to remove paper

BTP-L580 User’s Manual 36APPENDIX: FEED button Configuration Parameter setting (configuring) by Feed button 1) Hold the

BTP-L580 User’s Manual 37¾ Parameter setting by Feed button ¾ Setting configuration of the printer

BTP-L580 User’s Manual 38¾ Configuration of the serial interface CommunicationBaud Rates (defaul

BTP-L580 User’s Manual 3Declarations If you need this manual, please comply with the Clause as below. If you disagree wi

BTP-L580 User’s Manual 39¾ Setting Mechanism and Hardware Mech. & HardwarePower Supply (default: normal

BTP-L580 User’s Manual 40¾ Print Setting Print SettingCode Page (default: PC 437) >7 Choices:

BTP-L580 User’s Manual 41 ¾ Paper Near-end Sensor setting Note: Paper Near-end Sensor setting is not a de

BTP-L580 User’s Manual 42¾ Set Default Configuration Set default configSet printer to default config >2

BTP-L580 User’s Manual 4improve products as new technology, components, software, and firmware become available. If user

BTP-L580 User’s Manual 5Warnings and Cautions Warning: Items shall be strictly followed to avoid damages to body an

BTP-L580 User’s Manual 6environmentally responsible manner in accordance with WEEE directive. Contact us In CHINA: Ad

BTP-L580 User’s Manual 7General Safety Instruction Before installing and using the printer, please read the following it

BTP-L580 User’s Manual 8and other devices that may cause the fluctuation in voltage. 8) Disconnect the power cord if th